Fundamentals: The Address Resolution Protocol

Janos Pasztor

In two previous articles we discussed how Ethernet and the Internet Protocol work, but we’ve glossed about a very important aspect of the two: how does a computer or a router know which MAC address to send an IP packet to?

In case of IP version 4 the answer is the Address Resolution Protocol, whereas in IPv6 it’s called Neighbor Discovery Protocol. This article will detail the Address Resolution Protocol.

ARP builds on top of Ethernet itself, the communication is done by sending single Ethernet frames. As a first example, let’s look at a lookup for an IP address.

Let’s say a router wants to know the MAC address of In this case it would send out an ARP Request packet that translates to Who has The source address of this Ethernet frame will be the MAC address of the device sending the request, the destination will be the broadcast MAC of FF:FF:FF:FF:FF:FF. This address means that switches on the network will forward the packet to all devices.

However, the ARP protocol has its own source and destination fields, but they are used a little differently. For an ARP request the destination MAC in the ARP packet will be 00:00:00:00:00:00 instead of FF:FF:FF:FF:FF:FF. The all-zero mac is equivalent to unspecified.

Is this confusing? Yepp, it is. The source and destination MAC are present in both the Ethernet layer and the ARP packet. And yes, they may be different. But more on that later.

ARP caching

As you might imagine, sending an ARP request for every single packet is quite expensive. That’s why all devices cache ARP responses, and they do that for quite a long time. If you run on Linux you can check the ARP table with the following command:

ip neigh

Gratuitous ARP

Sometimes ARP requests and replies can be sent gratuitously, or in other words, out of the normal order. There are many reasons to do this, but there is one important aspect to keep in mind: if a device / computer receives an ARP response packet, the results are cached. And what’s even more peculiar, the receiving device doesn’t care if the sending device and the information contained within the ARP packet are in any relation to each other.

In other words, any device can send an ARP packet to change the ARP table of other devices. Sounds like a source of trouble? Well, it is. However, there are legitimate uses too, so you can’t just change this behavior.


Let’s talk a little bit about legitimate uses of Gratuitous ARP. First, let’s look at clustering. It is quite common pattern when building clusters to create a so-called virtual IP or VIP. This VIP is shared between two or more machines in a way that at any given time only one device “has” the IP.

However, when a failover is desired, a different machine takes on the VIP in addition to its original IP. The router, however, still thinks the IP is on the old host and it will stay like that for a while. To fix this issue, the new owner of the IP will send a gratuitous ARP packet to the router, triggering it to update its ARP table.


Modern switches (networking equipment) keep track of which MAC address is on which port. Sending an ARP packet can be used to inform the switch that a given MAC address is on a given port. This is especially important when virtual machines are moved between hosts.

Preloading ARP tables

When network links come up (e.g. when a cable is plugged in) modern network stacks will send a gratuitous ARP packet to preload the neighboring machines’ ARP tables with the IP addresses on that host.

IP address usage checking

Gratuitous ARP can be used to check if an IP address is already in use on a network. This is often done if a network works with self-assigned IPs. It is also useful to detect IP address conflicts. If a machine receives an ARP packet with its own IP but a different MAC, it knows that the IP is in use elsewhere.

ARP spoofing

I mentioned previously that the MAC address is present both in the Ethernet frame and the ARP packet. The sad state of affairs is that the two are in no relation to each other. Any host can send an ARP request or reply to any other host with any MAC address on the ARP layer. For example, we could poison the ARP cache of a target machine like this:

nping \
  --source-mac <attackers MAC> \
  --dest-mac <victim MAC>
  --arp-type ARP-reply \
  --arp-sender-mac <attackers MAC> \
  --arp-sender-ip <router IP> \
  --arp-target-mac <victim MAC> \
  --arp-target-ip <victim IP> \
  <victim IP>

This will effectively poison the victims ARP cache so that they send any traffic they intended to send the router to your machine.

You could even go one step further and, instead of specifying your own MAC, send the traffic elsewhere. Yes, ARP is basically a free-for-all.


ARP is a very basic protocol, but due to its open nature it lets you do all kinds of shenanigans. When ARP fails, it is quite hard to debug because its functionality is taken for granted.